Csaba
PLEASE READ FULL DESCRIPTION BEFORE PURCHASING!!!!
THESE ARE PRINTED ON FDM PRINTERS NOT RESIN PRINTERS. THERE WILL BE LAYER LINES THAT DO NOT SHOW IN THE 3D RENDERED MAIN IMAGE OF THIS LISTING!!!
This is part of a selection of detailed 3D Prints designed by the amazing Bergman.
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces).
Assembly may be required on this model such as the wheels.
The scales of these half tracks are correct however over time Miniatures have increased in size and are no longer true to scale. So, these half tracks may or may not match your miniatures 100%.
For dimensions, please see the provided image. There are in millimetres and are an approximation only. Some vehicle variants may vary in size slightly.
The main images on this listing are 3d digital renders of the buildings and are to show you an example of the Tanks only. The actual product is 3D printed on FDM printers and so will have layer lines and sometimes minor defects that can happen during 3D printing. Also, for smaller scales 15mm/1:100 & 10mm/1:144 some details may be lost due to decreasing the size of the model. On some occasions I may snip parts off and put them in a bag if I do not think they will survive transportation in the post. I will advise of this before posting. Due to the amount of supports that is printed with this model then underside of parts may be rougher than normal.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very, very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright Bergman, provided as an officially licensed seller
PLEASE READ FULL DESCRIPTION BEFORE PURCHASING!!!!
THESE ARE PRINTED ON FDM PRINTERS NOT RESIN PRINTERS. THERE WILL BE LAYER LINES THAT DO NOT SHOW IN THE 3D RENDERED MAIN IMAGE OF THIS LISTING!!!
This is part of a selection of detailed 3D Prints designed by the amazing Bergman.
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces).
Assembly may be required on this model such as the wheels.
The scales of these half tracks are correct however over time Miniatures have increased in size and are no longer true to scale. So, these half tracks may or may not match your miniatures 100%.
For dimensions, please see the provided image. There are in millimetres and are an approximation only. Some vehicle variants may vary in size slightly.
The main images on this listing are 3d digital renders of the buildings and are to show you an example of the Tanks only. The actual product is 3D printed on FDM printers and so will have layer lines and sometimes minor defects that can happen during 3D printing. Also, for smaller scales 15mm/1:100 & 10mm/1:144 some details may be lost due to decreasing the size of the model. On some occasions I may snip parts off and put them in a bag if I do not think they will survive transportation in the post. I will advise of this before posting. Due to the amount of supports that is printed with this model then underside of parts may be rougher than normal.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very, very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright Bergman, provided as an officially licensed seller
PLEASE READ FULL DESCRIPTION BEFORE PURCHASING!!!!
THESE ARE PRINTED ON FDM PRINTERS NOT RESIN PRINTERS. THERE WILL BE LAYER LINES THAT DO NOT SHOW IN THE 3D RENDERED MAIN IMAGE OF THIS LISTING!!!
This is part of a selection of detailed 3D Prints designed by the amazing Bergman.
These are made from either Grey or Black PLA (Colour will depend on what we have currently in stock & shades may differ between pieces).
Assembly may be required on this model such as the wheels.
The scales of these half tracks are correct however over time Miniatures have increased in size and are no longer true to scale. So, these half tracks may or may not match your miniatures 100%.
For dimensions, please see the provided image. There are in millimetres and are an approximation only. Some vehicle variants may vary in size slightly.
The main images on this listing are 3d digital renders of the buildings and are to show you an example of the Tanks only. The actual product is 3D printed on FDM printers and so will have layer lines and sometimes minor defects that can happen during 3D printing. Also, for smaller scales 15mm/1:100 & 10mm/1:144 some details may be lost due to decreasing the size of the model. On some occasions I may snip parts off and put them in a bag if I do not think they will survive transportation in the post. I will advise of this before posting. Due to the amount of supports that is printed with this model then underside of parts may be rougher than normal.
This listing is unpainted and due to the nature of 3D printing there will be print lines throughout the print, this is because FDM printers print in layer lines. There may be some bumps and blemishes that are not part of the original design. In some cases, this can actually improve the look, making the print look more rugged and worn. However, sanding with sandpaper and/ or a sharp craft knife can typically get rid of most of these. On some occasions warping can happen in the bottom corners, these can be filled in once assembled. Stringing (very, very thin strings of plastic) can also occur between points. I clean these up as much as I can but sometimes miss them. They can either be cut away or even melted (please take care not to heat the plastic up too much) away with a hairdryer. The underside of the prints may not be a smooth finish or may have white patches. This is because I often use a glue stick to help stick the print to the print bed.
Source models are copyright Bergman, provided as an officially licensed seller
